软件和固件存档

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

Bug Fixes

• When an interfering DECT device is transmitting nearby an MXW Access Point, the Access point may occasionally drop the connection to microphones 1-4. To recover mic connectivity, reset the Access Point.
  • Examples of interfering DECT devices are other MXW Access Points that are not on the same subnet as the affected Access point; however, in many cases, the interfering DECT devices are wireless headsets for wired desk telephones.
• MXW microphones intermittently drop off the Monitor status screen and their LED turns from green to flashing red for 10 to 30 seconds before recovering back to green, and then recovering their status activity on the Monitor screen. This may occur in environments with large reflective surfaces, such as windows, large LED monitors, and auditoriums with high walls and ceilings. These environments introduce RF reflections that interfere with the heartbeat signal from an MXW Access Point to a microphone. Microphones overcompensate for the interference and lose connectivity with the Access Point, restarting the scan process (seen as a red blinking LED) to find a valid Access Point signal.

Known Issue

• SystemOn 3.0.1 is compatible with MXW 6.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”

Notes

• To operate MXW version 6.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
  • SCM820 1.3.3
  • Shure Web Device Discovery 1.2
  • Shure Update Utility 2.4.3
  • SystemOn 3.0.1

Initial Release

Notes

• Designed to work with ACOS3 dual-interface and contactless cards, including Shure “MXCDualCard-10PK”
• Designed to work with the ACR1252U USB NFC reader/writer from Advanced Card Systems Ltd. (requires driver version 4.2.8.0 or above)
• Compatible with 64-bit Windows 7 and 10 installations

Improvements

• Changed the version number to 1.6.19 to allow all PSM1000 devices in a configuration to have the same version number
• Bug fixes

Notes

• To operate PSM1000 devices version 1.6.19 with other Shure networked systems, see the following list of supported minimum versions:
  • AXT600 2.1.22
  • Axient Digital 1.1.43
  • ULX-D 2.2.24
  • Wireless Workbench 6.12.5
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

New Feature

• Support for P10R+

Notes

• To operate PSM1000 devices version 1.6.19 with other Shure networked systems, see the following list of supported minimum versions:
  • AXT600 2.1.22
  • Axient Digital 1.1.43
  • ULX-D 2.2.24
  • Wireless Workbench 6.12.5
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

IMPORTANT

To update Shure Update Utility version 2.4 or earlier to version 2.4.3, download and re-install from www.shure.com/SUU or through Help > Check for Shure Update Utility updates.

IMPROVEMENTS

• Support for the following products
  • MXCWAPT Access Point Receiver
  • MXCW640 Wireless Conference Unit
  • MXCWNCS Networked Charging Station
  • SBC220 2-Bay Networked Charging Station
  • SBC240 2-Bay Networked Charging Station
  • P10R+ Bodypack Receiver
• Bug fixes

KNOWN ISSUES

• PSM1000 devices with firmware version 1.1.0 or earlier must use Shure Update Utility version 2.4.1 or older.
  • Version 2.4.1
    • 32-bit Windows 7, 8, 10
    • 64-bit Windows 7, 8, 10
    • 64-bit Mac OS X 10.10-10.12
  • Previous Versions
• Selecting "Help" > "Check for Shure Update Utility updates" will open Shure.com, which offers the latest version of Shure Update Utility to download. Shure Update Utility version 2.4.2 or greater will not automatically detect new versions.
• 32-bit Windows:
  • To update Shure Update Utility version 2.2.2 or earlier on a 32-bit Windows system, download version 2.4.2 or greater for 32-bit systems to re-install the software. Older versions of Shure Update Utility will not detect new updates of Shure Update Utility that support 32-bit systems.
  • Shure Update Utility version 2.4.3 for 32-bit systems is compatible with Wireless Workbench 6 version 6.12.1 and earlier.
• Attempts to download ULXD6/8 transmitter firmware to a ULX-D or QLX-D receiver that is not at the minimum firmware version, shown below, will fail. To update firmware for ULXD6/8 transmitters with ULX-D or QLX-D receivers:
  • Update receivers to the following minimum versions:
    • ULXD4, ULXD4D, ULXD4Q Receivers 2.1.16
    • QLXD4 Receivers 2.1.5
  • Using Shure Update Utility, download ULXD6/8 transmitter firmware to the receivers.
  • Using the FW Update menu on a receiver, update transmitters
• Microflex Wireless devices running version 1.X firmware must first be updated to version 2.0.5 before being updated to version 3.X or later.
• USB-C MacBook Pro laptops with the Touch Bar running macOS High Sierra will fail to discover GLX-D devices. We are currently investigating this issue.

NOTES

• Shure Update Utility is supported on the following operating systems:
  • Windows 7, 8 and 10
  • Mac OS X El Capitan (10.11), Sierra (10.12), and High Sierra (10.13)
• Installing Shure Update Utility on Windows will also prompt the installation of a USB driver, which must be installed to support updating USB devices, such as GLX-D.
• USB 2.0 Devices
  • KSE1500, SHA900, and GLX-D must be updated one-at-a-time.
  • USB hubs are not recommended when updating USB 2.0 connected devices. Always connect these devices directly to a USB on the computer running Shure Update Utility.
• Shure Update Utility 2.4.2 or greater for 64-bit systems is compatible with Wireless Workbench 6.12.2 or later.
• Shure Update Utility 2.4.2 or greater for 32-bit systems is compatible with Wireless Workbench 6.12 or earlier.

Improvements

• Support for Axient Digital frequency bands
  • 470 MHz – 608 MHz (G57)
  • 470 MHz – 608 MHz and 614 – 616 MHz (G57+)

Notes

• User Guide
• To operate Axient 2.1.22 devices with other Shure systems and software, see the following list of minimum versions:
  • Axient Digital 1.1.43
  • UR4 UHF-R receiver 1.171
  • UR3 Plug-on Transmitter 1.0.0.16
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULX-D ULXD4X Receivers 2.2.24
  • QLX-D QLXD4 Receiver 2.2.11
  • PSM1000 P10T Transmitter 1.6.19
  • SBRC Shure Battery Rack Charger 1.1.X
  • Shure Update Utility 2.4.2
  • ShurePlus Channels 1.4.2
  • Wireless Workbench 6.12.5

Improvements

• Support for Axient® Digital with ADX Series Transmitters
• Bug fixes
• Added User Guide (About > User Guide)

Notes

• Monitors and controls Axient® Digital, Axient®, UHF-R®, ULX-D® Digital and QLX-D® Digital, and PSM®1000 wireless systems
• Compatible with iPhone, iPad, and iPod touch running iOS 10 – 11
• An 802.11n or 802.11ac wireless router is recommended
• For best results update the Shure wireless system’s firmware using the Shure Update Utility.
• ShurePlus Channels Wifi Guidlines

新功能

• 增加对采用ADX系列发射机的Axient® Digital的支持
• 增加对SBC220联网插座充电器的支持

改进功能

• 增加对频率分集模式下系统的支持，从频率分集对的每个通道中强制进行1 MHz频率分离

          ⁃这包含Axient Digital A频段接收机的G57+频段在内。

• 从日本电视图谱上删除了TV 53。
• Monitor View和Timeline作了大量性能提升，包括解决了可能导致内存使用过多或应用程序滞后的问题。
• 修复了一般的漏洞

已知问题

• 当电视频道宽度不是6 MHz时，导出电视排除文件至频谱管理器可能导致电视排除范围错误。
• 运行2.0.28或更早版本固件的ULX-D接收机在固件更新至2.1或更高版本后，重新发现设备可能触发“设置冲突”。设备本身并没有问题——只是2.1版本新增加的一项属性而已。要解除警报，请选择要保留的属性，来解决此“设置冲突”。
• 在某些特定频道出现过载的情况下，ULX-D接收机报告的“音频合并”会报告所有频道都出现“音频过载”，而不会指出特定频道。
• 使用Axient Digital FD-Override（在FD-S中，选择锁定至Rx 1/2/自动开关）时，如果两个FD通道都未显示，则会出现“Timeline系统事件”。
• 在显示的ULXD6/8发射机“在线活动发射机”的“Timeline系统事件”中，事件描述不会始终包括发射机设备ID。
• 在Mac操作系统上，当用户打开演出记录文件，并启动“频率分析”对话框时（通过选中复选框并按“分析”），“频率协调”选项卡可能停止响应键盘输入（例如使用键盘来编辑或删除频率）。为了解决这个问题，请选择应用程序中的另一个选项卡（例如“目录”或“监控”），然后重新选择“频率协调”选项卡。
• Master模式下的SLX和ULX频率无法在协调工作区中手动输入。但能够对其进行协调和分析。⁃ 设备首次上线时，登录的警报可能会列出设备参数及各项值，因为即便参数值本身未发生变化，也会被警报发现。⁃ 某些便携式腰包与SBC220（P3RA、 P9HW和UR5）不兼容，因而不能通过WWB远程监控充电状态和其他属性。使用SBC220时这些便携式腰包仍可进行充电，只是不能通过WWB查看电池充电百分比或其他属性。

说明

• Wireless Workbench软件要顺利运行，您必须以管理员身份登录。（如有问题，请咨询IT部门。）
• 标签添加至演出记录文件，但未分配给任何设备时，不会保存在演出记录文件中。
• 打开较旧版本Wireless Workbench创建的演出记录文件时，可能会在文件加载后出现“设置冲突”对话。这是因为，新支持的硬件参数使用了已更新的固件版本。要保留演出记录文件的所有设置，请选择“保留所有设置：Wireless Workbench”。
• 对于运行Windows 7的机器，无论已连接舒尔设备的IP寻址是什么，当机器退回到169.254.xxx.yyy回退IP地址时，Wireless Workbench都不会发现设备。要解决此问题，请执行以下一种操作：将DHCP服务器加入到您的网络，将您的机器和舒尔设备设置为接受IP自动寻址。将您机器的IP地址静态分配到169.254.xxx.yyy回退子网，确保IP地址与退回的原始地址不同。

Important

• This version applies to AD1, AD2, ADX1, ADX1M, and ADX2 transmitters

New Feature

• Initial firmware for ADX1, ADX1M, and ADX2 transmitters.

Improvements

• Support for new or changed frequency bands:
  • Israel (R52) 794 MHz – 806 MHz
  • U.S. (G57) 470 MHz – 608 MHz: Now excludes 600 MHz guard bands
  • U.S. (G57+) 470 MHz – 608 MHz and 614 – 616 MHz: Includes UHFTV + Guard bands.
• Menu UI improvements
• Bug fixes

Notes

• User Guides: AD1 | AD2
• AD1/2 and ADX1/1M/2 version 1.1.43 is compatible with devices on version 1.1.43 and below, but it is recommended to update all devices used together to the same firmware version.
• To operate AD1/2 and ADX1/1M/2 version 1.1.43 devices with other Shure systems and software, see the following list of minimum versions:
  • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.1.43
  • Axient Digital AD4D/Q Receivers 1.1.43
  • Axient AXT600 Spectrum Manager 2.1.22
  • SBC240/840/840M Chargers 1.1.43
  • SBRC Shure Battery Rack Charger 1.1.X
  • Shure Update Utility 2.4.2
  • ShurePlus Channels 1.4.2
  • Wireless Workbench 6.12.5

New Feature

• Initial firmware for the SBC840M 8-Bay Charger.

Notes

• To operate SBC840M version 1.1.43 with other Shure devices and software, see the following list of minimum versions:
  • Axient Digital ADX1 Transmitters 1.1.43
  • Shure Update Utility 2.4.2
  • Wireless Workbench 6.12.5