软件和固件存档

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

Bug Fixes

• When an interfering DECT device is transmitting nearby an MXW Access Point, the Access point may occasionally drop the connection to microphones 1-4. To recover mic connectivity, reset the Access Point.
  • Examples of interfering DECT devices are other MXW Access Points that are not on the same subnet as the affected Access point; however, in many cases, the interfering DECT devices are wireless headsets for wired desk telephones.
• MXW microphones intermittently drop off the Monitor status screen and their LED turns from green to flashing red for 10 to 30 seconds before recovering back to green, and then recovering their status activity on the Monitor screen. This may occur in environments with large reflective surfaces, such as windows, large LED monitors, and auditoriums with high walls and ceilings. These environments introduce RF reflections that interfere with the heartbeat signal from an MXW Access Point to a microphone. Microphones overcompensate for the interference and lose connectivity with the Access Point, restarting the scan process (seen as a red blinking LED) to find a valid Access Point signal.

Known Issue

• SystemOn 3.0.1 is compatible with MXW 6.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”

Notes

• To operate MXW version 6.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
  • SCM820 1.3.3
  • Shure Web Device Discovery 1.2
  • Shure Update Utility 2.4.3
  • SystemOn 3.0.1

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

Bug Fixes

• When an interfering DECT device is transmitting nearby an MXW Access Point, the Access point may occasionally drop the connection to microphones 1-4. To recover mic connectivity, reset the Access Point.
  • Examples of interfering DECT devices are other MXW Access Points that are not on the same subnet as the affected Access point; however, in many cases, the interfering DECT devices are wireless headsets for wired desk telephones.
• MXW microphones intermittently drop off the Monitor status screen and their LED turns from green to flashing red for 10 to 30 seconds before recovering back to green, and then recovering their status activity on the Monitor screen. This may occur in environments with large reflective surfaces, such as windows, large LED monitors, and auditoriums with high walls and ceilings. These environments introduce RF reflections that interfere with the heartbeat signal from an MXW Access Point to a microphone. Microphones overcompensate for the interference and lose connectivity with the Access Point, restarting the scan process (seen as a red blinking LED) to find a valid Access Point signal.

Known Issue

• SystemOn 3.0.1 is compatible with MXW 6.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”

Notes

• To operate MXW version 6.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
  • SCM820 1.3.3
  • Shure Web Device Discovery 1.2
  • Shure Update Utility 2.4.3
  • SystemOn 3.0.1

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

Bug Fixes

• When an interfering DECT device is transmitting nearby an MXW Access Point, the Access point may occasionally drop the connection to microphones 1-4. To recover mic connectivity, reset the Access Point.
  • Examples of interfering DECT devices are other MXW Access Points that are not on the same subnet as the affected Access point; however, in many cases, the interfering DECT devices are wireless headsets for wired desk telephones.
• MXW microphones intermittently drop off the Monitor status screen and their LED turns from green to flashing red for 10 to 30 seconds before recovering back to green, and then recovering their status activity on the Monitor screen. This may occur in environments with large reflective surfaces, such as windows, large LED monitors, and auditoriums with high walls and ceilings. These environments introduce RF reflections that interfere with the heartbeat signal from an MXW Access Point to a microphone. Microphones overcompensate for the interference and lose connectivity with the Access Point, restarting the scan process (seen as a red blinking LED) to find a valid Access Point signal.

Known Issue

• SystemOn 3.0.1 is compatible with MXW 6.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”

Notes

• To operate MXW version 6.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
  • SCM820 1.3.3
  • Shure Web Device Discovery 1.2
  • Shure Update Utility 2.4.3
  • SystemOn 3.0.1

改进功能

• 支持更新至ULX-D
• 修复漏洞

已知问题

• 当电视频道带度不是6 MHz时，导出电视排除文件至频谱管理器可能导致电视排除范围错误。
• 运行2.0.28或更早版本固件的ULX-D接收机在固件更新至2.1或更高版本后，重新发现设备可能触发“设置冲突”。设备本身并没有问题——只是2.1版本新增加的一项属性而已。要解除警报，请选择要保留的属性，来解决此“设置冲突”。
• 在某些特定频道出现过载的情况下，ULX-D接收机报告的“音频合并”会报告所有通道都出现“音频过载”，而不会指出特定通道。
• 使用Axient Digital FD-Override（在FD-S中，选择锁定至Rx 1/2/自动开关）时，如果两个FD通道都未显示，则会出现“Timeline系统事件”。
• 在显示的ULXD6/8发射机“在线活动发射机”的“Timeline系统事件”中，事件描述不会始终包括发射机设备ID。
• 在Mac操作系统上，当用户打开演出记录文件，并启动“频率分析”对话框时（通过选中复选框并按“分析”），“频率协调”选项卡可能停止响应键盘输入（例如使用键盘来编辑或删除频率）。为了解决这个问题，请选择应用程序中的另一个选项卡（例如“目录”或“监控”），然后重新选择“频率协调”选项卡。
• master模式下的SLX和ULX频率无法在协调工作区中手动输入。但能够对其进行协调和分析。
• 使用AXT400接收机扫描时，“现场扫描设置”对话框中的“频道预设”值不会始终与接收机当前所选频道保持同步。可手动调整“频道预设”值，扫描任何支持的范围。
• 设备首次上线时，登录的警报可能会列出设备参数及各项值，因为即便参数值本身未发生变化，也会被警报发现。
• 某些便携式腰包与SBC220（P3RA、 P9HW和UR5）不兼容，因而不能通过WWB远程监控充电状态和其他属性。使用SBC220时这些便携式腰包仍可进行充电，只是不能通过WWB查看电池充电百分比或其他属性。

说明

• Wireless Workbench软件要顺利运行，您必须以管理员身份登录。（如有问题，请咨询IT部门。）
• 标签添加至演出记录文件，但未分配给任何设备时，不会保存在演出记录文件中。
• 打开较旧版本Wireless Workbench创建的演出记录文件时，可能会在文件加载后出现“设置冲突”对话。这是因为，新支持的硬件参数使用了已更新的固件版本。要保留演出记录文件的所有设置，请选择“保留所有设置：Wireless Workbench”。
• 对于运行Windows 7的机器，无论已连接舒尔设备的IP寻址是什么，当机器退回到169.254.xxx.yyy回退IP地址时，Wireless Workbench都不会发现设备。要解决此问题，请执行以下一种操作：

          将DHCP服务器加入到您的网络，将您的机器和舒尔设备设置为接受IP自动寻址。

Important

• ULX-D receivers must be on version 2.2.24 or higher and QLXD4 receivers on version 2.2.11 or higher in order to be used with SBC250 charging stations.
• ULX-D receivers must be on version 2.1.6 or higher and QLXD4 receivers on version 2.1.5 or higher in order to be used with SBC450/850 charging stations.

Improvement

• Changed version number to allow all ULX-D devices in a configuration to have the same firmware version.

Known Issue

• SBC250/450/850 devices are not compatible with SystemOn 2.0-3.0.1

Notes

• SBC450/850 User Guide
• To set up ULXD6/8 transmitters to receive firmware updates while docked in SBC250/450/850 Networked Charging Stations, follow these steps:
  1. Place transmitters on a charging station and ensure the charging station is connected to the network.
  2. Launch Shure Update Utility to find firmware updates.
  3. Download updates and select Send Updates.
• To operate SBC250/450/850 version 2.3.4 with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.4
  • QLX-D QLXD4 Receivers 2.2.11
  • Wireless Workbench 6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Changed version number to allow all ULX-D devices in a configuration to have the same firmware version.

Known Issues

• New hardware revisions of ULX-D version 2.3.4 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• If your ULXD1/2 transmitter is on version 2.2.23, updating to version 2.2.24 will unexpectedly reset your ULXD1 to its factory default settings and your previous settings will need to be recovered via IR sync.
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.4 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD4/4D/4Q Receivers 2.3.4
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench  6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Changed version number to allow all ULX-D devices in a configuration to have the same firmware version.

Known Issues

• New hardware revisions of ULX-D version 2.3.4 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• If your ULXD1/2 transmitter is on version 2.2.23, updating to version 2.2.24 will unexpectedly reset your ULXD1 to its factory default settings and your previous settings will need to be recovered via IR sync.
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.4 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD4/4D/4Q Receivers 2.3.4
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench  6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Changed version number to allow all ULX-D devices in a configuration to have the same firmware version.

Known Issues

• New hardware revisions of ULX-D version 2.3.4 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• If your ULXD1/2 transmitter is on version 2.2.23, updating to version 2.2.24 will unexpectedly reset your ULXD1 to its factory default settings and your previous settings will need to be recovered via IR sync.
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.4 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD4/4D/4Q Receivers 2.3.4
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench  6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Support new hardware revisions of ULX-D. New revisions can't be downgraded below version 2.3.4.

Known Issues

• New hardware revisions of ULX-D version 2.3.4 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.4 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.4
  • SBC250/450/850 Networked Charging Stations 2.3.4
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • PSM1000 1.6.19
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench 6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Support new hardware revisions of ULX-D. New revisions can't be downgraded below version 2.3.4.

Known Issues

• New hardware revisions of ULX-D version 2.3.4 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.4 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.4
  • SBC250/450/850 Networked Charging Stations 2.3.4
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • PSM1000 1.6.19
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench 6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2